Great news! We've located your Anilam unit in our database of repaired units.
If you require testing or repair services for your Anilam unit, don't hesitate to reach out to us at 1-336-969-0110.
We pride ourselves on providing fair estimates and offer a generous one-year warranty.
Simply fill out the Anilam Service Comment Form below with any questions or inquiries, and we'll be happy to assist you!
Recent Questions
-
Anilam - where does the R5232 connect to
-
Anilam - We have not used the machine with the Anilam SR1100 for several years.
Replaced the battery and tried to reload the software
-
Anilam - i have anilam 1100 control with bridge port i have change Battery but now i have start machine y axis go to Negative directio
-
Anilam - Hi,
I have a Arnault Samua machine ZXV1 which is fitted with Anilam Crusador 2 controller and Indramat TRM2 DC servo drive
-
Anilam - I have no docs on servo power wiriing. Enable servo power on back of the crusader to does nothing.
Do I have to reverse en
-
Anilam - i need servo Y servo wiring diagram
-
Anilam - i need the Anilam Anilam Crusader II wiring Diagram
abdoaakl-cairo - egypt-abdoaakl1@yahoo.com
thanks for you.
-
Anilam - Hi I has a problem with a Lagun CNC with control anilam cruzader II I would like to buy the manual
-
Anilam - We have a bridgeport with the 1100 anilam control on it. About a year ago the feed on the x @ y stopped working. Not able t
-
Anilam - 1100m on a bridgeport style knee mill,
i was told the mother board is out. anyway to check it and how much would a replaceme
-
Anilam - When I booted machine COMS battery state low
Standard COMS setup
Advance COMS setup
auto configuration with BIOS defaults
-
Anilam - DEAR SIR
ORDNANCE FACTORY, MINISTRY OF DEFENCE, TIRUCHIRAPALLI- 620 016, (TAMILNADU STATE), SEARCHING FOR CNC SYSTEM AND
-
Anilam - Daer Sir,
We are working on Anilam Since 4 years. We made many mould on it and machine working quality is good. So that is
-
Anilam - The Z axis is inoperative, manual movement of the Z axis results in the power contactor tripping out. This is the same contac
-
Anilam - WE NEED ELECTRICAL CIRCUIT DIAGRAM+REPAIRING MANUAL FOR ANILAM CRUSADER-2(3-AXIS).WHAT WILL BE THE CHARGES FOR THE SAME.
-
Anilam - Sir,
We have purchased 1 used Ernault Samoua milling Machine model ZHV-1.
travels of the machine x,y,z are 710*270*400.
-
Anilam - Hi john I called you earlier about connectors for servo driver card. We had
cmos setting problems and fixed them on the 110
-
Anilam - I have an Anilam 1100 control that wont keep the cmos settings. The control starts to boot up but then tells me to push F2 to
-
Anilam - Mr.Umer Azhar Rana
We are in pakistan and we have all of Anilam Cursader II Help tell me in deta
-
Anilam - Russell,
I may know where theres a used control \"head\" with a functional touch pad membrane. I sold one to a friend seve
-
Anilam - hello, i have a cruasder m controller that has a broken membrane face where you push the program buttons. can you supply a n
-
Anilam - We have an Anilam machine that is died.
The screen show +x or -x limit. Can you help me?...
Thanks..
-
Anilam - i have a milling machine with a anilam crusader when i start up the machine he gives a error 18 after 3 seconds and the x as
-
Anilam - I have a Anilam Crusader II on my Milling Machine not working plz help me to know weather I can Retrofit an other unit with m
-
Anilam - sorry i have softlimit problem but do not know how to remove
-
Anilam - Dear Sir
How we adjust the backlash in machine
thanks
AMIN
-
Anilam - Did you reset the unit before you tried to jog it? Does it move at all before the error 18 code shows up?
Christopher Atw
-
Anilam - we got a new cnc lathe in our shope with an anilam crusader II control but if we try to jog the axis in manual mode you get a
-
Anilam -
One of the PCB boards in the controller came off it\'s mountings during transport and was damaged. The servos do not power
