|
|
 |
 |
 |
Repair Services for Industrial and Commercial Customers |
|
|
|
Taylor ElectronicsTaylor 3107 Windspeed IndicatorAfter reading your comments about your sensor, I realized the magnet may be one of the culprits on this issue. Over time moisture accumulates in the magnet and may weaken the field to the induction coil. The induction coil in the Taylor anemometer heads are often weakened by time - temp changes etc. 30+ yrs of use. The coil end braids come undone, but yours is still reading out. There are also two capacitors in the back of the meter and they sometimes lose charge during wind lulls. There are also two adjusting potentiometers in the back of the meter. These can calibrate the windspeed. I find taking a small 6v battery sometimes fills the capacitors back to full thus making the windspeed work again. Just make sure if you do this, to do it momentarily and without the generator unit attached. The Taylor also has a rubber piece in the center of the magnet, make sure it isn\'t rubbing the bearing plate, it slows the cup operation. You might want to consider a set screw in the outer cup hub, Taylor windspeed generators have a tendency to blow off during windstorms. I have had several 3107s. They are quite accurate if maintained.
-Matt | Return Home to Taylor Electronics
View Parent Post
|
If you have any technical questions or
wish to offer technical information about any Taylor Electronics units then
fill out the form below.
No Soliciting...
-
Taylor Electronics - I have a Taylor Weatherscope but I need the outdoor parts.
Are those available?
-
Taylor Electronics - I own an original Taylor Windscope Wind Vane w/ original "Wind Direction" indicator.
After 30 years of service it
-
Taylor Electronics - Hello. Did this unit ever sell? I\'m interested!
-
Taylor Electronics - I have a new weatherscope still in box. Call and make an offer 603 608 9670
-
Taylor Electronics - Hello:
I have acquired a Weatherscope by Taylor (wooden box with 4 gauges) Brand new, never used. It has all the parts exce
-
Taylor Electronics - Do you have a speed cup for a 3108C assembly or do I have to buy the total roof replacement?
Thank you.
-
Taylor Electronics - How do I contact you to discuss purchase? I am interested
thanks - TomR - 215.589.0686
-
Taylor Electronics - Hi:
I am trying to repair/replace my Weatherscope but I do not know what a 3108 looks like. Mine is in a chery case and h
-
Taylor Electronics - need to replace entire speed cup assembly that fits on shaft.
please, advise.
-
Taylor Electronics - I have a NOS Weatherscope 3108 new in the original box. Has never been unpacked or installed.
I would like to sell the who
-
Taylor Electronics - Do you sell, or tell me where I can get parts.Thank you
-
Taylor Electronics - Hello,
Is it possible to purshase a weatherscope or the entire roof mount with the speed and wind direction?
Best Regards,
-
Taylor Electronics - I would be extremely interested in your weaterscope if you still have it. I had one and would love to have a replacement for
-
Taylor Electronics - I have a complete station that was purchased new in 1976
and never used. Is there a market for such an item?
-
Taylor Electronics - I have the same thing as Leo. My Dad was a weatherman for the County and I inherited this. I would love to use it but I know
-
Taylor Electronics - Re; Taylor Model 3108
A repair person at my home has severly damaged my external thermometer prob/bulb and has also severed
-
Taylor Electronics - Hi Jeff I, also have a Taylor Weatherscope. I\'m missing the Anemometer & Wind Direction unit. Can you PDF the Booklet that c
-
Taylor Electronics - Have an old? Taylor Weatherscope (cannot find a Model Number) made by Taylor Instrument Company Rochester USA. Has four separ
-
Taylor Electronics - I have a Weatherscope by Taylor and the temperature probe is intact and works great, but the wind speed/direction thingie is
-
Taylor Electronics - I am looking for the anamometer cups of the above Taylor weatherscope. One of the cups broke in transit and I need a replace
-
Taylor Electronics - After reading your comments about your sensor, I realized the magnet may be one of the culprits on this issue. Over time mois
-
Taylor Electronics - David,
I too have become the owner of an older 3108c Weatherstation. I was fortunate enough to get the instruction booklet
-
Taylor Electronics - we are looking for parts that go from the back of our barameter to the tower. it is a old unit. The only thing I see on it is
-
Taylor Electronics - I would like to know if I can purchase the roof unit ( wind/speed indicator and wire )for the 3108 Weatherscope or if I can u
-
Taylor Electronics - The weathervane rod bent due to some unknown reason and when I took off the top I noticed the vectical shaft was also worn ve
-
Taylor Electronics - my SYBRON-TAYLOR has stopped recording the correct speed--at low wind speed the indicator wiggles only a small amount---at hi
A
B
C
D
E
F
G
H
I
J
K
L
M
N
O
P
Q
R
S
T
U
V
W
X
Y
Z
|
|
|
 |
|
 |
|
|
