Industrial Electronics Repair

Links Menu

Home
About Us
Repair Lab
Job Opportunities
Manufacture's Repaired
Forum
Get Quote
Repair Service Form
Monitor Repair
CNC Repair
Power Supply Repair

Search


Manufacture:

Part #:



Contact Menu


  • Industrial Electronics Repair
    931-E S. Main St #204,
    Kernersville, NC 27284

  • 1-(336)-969-0110

  •   

    Repair Services for Industrial and Commercial Customers

    Inventron

    Inventron Uni-Sonic System

    I have a Uni-Sonic Instruments System, Model EC 200-1 and T200-1-1-EP-N Serial No. 1841 (Date in service June 15, 1977). Broadcast frequency is 218 kHz. The vendor manual I have for this hardware is dated 1973. This application measures level of product and the voltage is inverted with zero reference point 14 ft from the mounting flange. The output signal is 0-5 VDC over 0-14 ft. My Operators report that the level alarms for this unit are actuating early, causing level of product in the vessel to be less than expected. I\'ve found very little other information onsite about operation of this equipment. Are you familar with this admittedly antiquated hardware, and if so, is it parts supported? Finally, Please advise
    Return Home to Inventron
    If you have any technical questions or wish to offer technical information about any Inventron units then fill out the form below.
    No Soliciting...





    • Inventron - all equipment ever manufactured by Inventron can be repaired at the factory. 734-513-7700 Arthur W. Merkl, General Manag
    • Inventron - I have a Uni-Sonic Instruments System, Model EC 200-1 and T200-1-1-EP-N Serial No. 1841 (Date in service June 15, 1977). Bro

    A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

    You can contact us at 1-(336)-969-0110
    Shipping/Receiving
    Industrial Electronics Repair
    931-E S. Main St #204,
    Kernersville, NC 27284
    Recent Questions
    • - Hello, hope I'm not bothering you, but could you help me out?. I have USDT TRX20 stored in the OKX wallet, and the recov
    • Esa Gv - Hi We are in the Flat glass industry and have a cnc cutting table with a Tria 4000 controller which the static RAM is corru
    • - Where can I find the owners, service and parts pdf manuals for this unit? Thank you, Terry
    • Scandialogic - Please send me pdf manual of inverter SCANDIALOGIC Slm 750 - 1
    • Industrial Electronics Repair - I have 2 Goring-Kerr (Thermo Fischer Scientific) DSP2 metal detectors that show the following faults in the status page: Faul
    • Dynamote - Trying to wire the remote switch inverters not working without it
    • - The machine is in beautiful condition, but due to not staying plugged in, the parameters have leaked off. Do you have a fix?
    • American Farmworks - do you sell American Farmworks 01479-92 board or the transformer on it? Please let me know cost and availability
    • Kouwa - I need an English manual for model KMV-150-M15-H serial 1906- M2328. I also need some sort of guidance with dip switch settin
    • Alpha Press Co. - do you offer repair for older alpha press machines? We are in need of someone who can fix the presses when they go down.
    • - Good morning, is it possible to repair polatech typ 92 EMC / 022 483 and ENCODER 022 257 . Thank you
    • - ayalace985@gmail.com
    • Socapel - Dear Concern, Please see under below detail then quote rate and also share performa invoice now on first p
    • Leland Faraday - I have a Leland Faraday 3 hp 230 volt single phase motor. It has 6 wires coming out of the motor, Black, Blue, Red, Green, Wh
    • Amf Paragon - do you have on/off timer pins for model MC 404-00. White for on and Black for off.
    • Velconic - My VELCONIC VLNBE-050P-XP servo drive have error code 05. What is this error 05 means ?? Tqvm !
    • - atlas copco system failure 7001
    • Rittenhouse - Hello, I purchased my 4 note-8 note melody door chime in 1995. It has been set up on a battery operation operation
    • Unknown - Make: Agco/hesston Model/Part:700715547 Quote:
    • Sparton - Looking for KT600F Keypad, for spare. Any? This is from an old post, Thanks John
    • Power Supply Repair - Make: Power Supply Repair Quote: I was needing my computer power fixed, how much does it cost to get a quote?
    • Teijin Seiki - Looking for a Vigoservo ASR30 Manual.
    • Quinton Crane - Hi, We have a Quinton Crane B481c PCB used in Bridgeport Vertical mill Series I. due to power fluctuations, this pcb is no
    • Dynamote - My husband recently passed away and while cleaning the garage I came across this item. It is a Dynamote B20-12 with CD, LVCO
    • Wohlenberg - Sir I need wohlenberg mcs-2 Tv cutting machine electrical diagram and service manual for English language
    • Atlas Copco - WE have two of the Atlas-Copco GA132 compressors onboard for our bulk handling system. One of them has an error code on the
    • Teijin Seiki - 25 drive alaram number
    • Scandialogic - Manual de inverter SCANDIALlogic
    • Toyo Denki - Manual book toyodenki v5100hg
    • Burgmaster - We are looking for oil seals for a Burgmaster Model 1-D the part number is A105406-00 we need 14 but will take what ever we c
    More Repair Questions.....


    A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
    Disclaimer: This website is not sanctioned or approved by any manufacturer listed.
    "Industrial Electronic Repair" is not an authorized distributor or representative
    for the listed manufacturers or tradenames.

    Home
    Repair Lab
    Manufactures Repaired
    Forum
    Get Quote
    Job Opportunities

    Hosted by

    Christ Servers
    Christian Web Hosting
    Powered by IERNC Content Management System CMS 1.0 2006
    A   B   C   D   E   F   G   H   I   J   K   L   M   N   O   P   Q   R   S   T   U   V   W   X   Y   Z  

    Contact Us



    Total Execution Time: 0.016983985900879 Seconds